Page History

Cause

INtime has a configuration problem that prevents the INtime kernel from starting.

Solution

Reinstall the A3200 and INtime. Refer to the procedure that follows.

1. Uninstall the A3200. Then restart the PC.
2. Uninstall INtime. Then restart the PC.
3. Install the A3200. Then restart the PC. The installation automatically installs and configures INtime again.

If reinstalling does not work or if the issue appears to have been caused by a Windows update, see Correcting Your A3200 Configuration in the Windows 10 Update Guide.

Cause

INtime has a problem that prevents the INtime node kernel from starting. Most This is commonly this can be attributed to some INtime specific settings or PC incompatibilities with INtime's RTOS (Real-Time Operating System). Examples include camera or Windows or BIOS settings that affect real time performance, camera/imaging software that utilize some type of utilizes an imaging/capture card installed on the computer, high end graphics cards, etc.

Solution

1. Reinstall the A3200 and

1. INtime. Refer to the procedure that follows.
   1. Uninstall the A3200. Then restart the PC.
   2. Uninstall INtime. Then restart the PC.
   3. Install the A3200. Then restart the PC

1. 1. . The installation automatically installs and configures INtime again.
2. Pass the FireWire/

1. HyperWIre card to Windows control, then back to INtime control.

1. 1. Open INtime Configuration
   2. Double click on INtime Device Manager

   3. Right click on the FireWire card and select Pass to INtime using Polling
      

      Expand
      title Figure 1-1
      Image Modified

      
      

   4. For HyperWire cards, Pass to INtime using MSI

      Expand
      title Figure 1-2
      Image Modified

3) Uninstall both A3200 and INtime (INtime is installed as a separate program). Reinstall A3200, therefore reinstalling INtime.

1. 1. 
      

2. Optimize the PC. This can be done by following the

1. Optimizing A3200 Performance

1. guide on our website. This includes a

• Specifically, try disabling Hyperthreading and/or Virtualization
• Optimization may help, however, if there are programs such as Cognex imaging software that use capture cards installed on the PC, Optimization may have no effect. These cards and software should be uninstalled to troubleshoot where the INtime Node errors come from.Note: Not all PC configurations will be able to run the INtime RTOS software (Real-Time Operating System) very well. If optimization does not work, there may be something about the PC's hardware, such as the CPU, that does not work well with Real-Time Operating Systems. 

1. list of Windows and BIOS settings

1. that are known to negatively affect real time performance.
   1. Note that not all PCs are compatible with A3200's real-time operating system. A list of supported PCs can be found here. Known problematic PC models are listed here. If optimization does not resolve the INtime error it may be that the PC model is simply not compatible with INtime, A3200's real time operating system. If this is the case, obtain a supported PC.
   2. If the above troubleshooting steps (including optimization) do not help to resolve this error, double check that the PC was thoroughly optimized.

1. Review the User Guide for Windows 10 Updates found on the Aerotech website. 
   
   1. In the event that these errors occurred shortly after a Windows update, you should review this guide

1. 1. . This guide has a few steps and suggestions that can be taken if errors start to appear after you updated Windows 10.

1. Upgrade

1. A3200

1. to

1. version 6.03.003 or newer for newer PC models.

1.  
   
   1. A3200 versions 6.02

1. 1. and earlier install INtime version 6.2, which does not run reliably on newer computer models.

1. 1. A3200 version 6.03.003

1. 1. uses INtime 6.3 and has been known to resolve this INtime

1. 1. node error on a few post-2017

1. 1. PC models.

1. Change INtime Node settings.
   1. Open

1. 1. INtime Configuration

1. 2. Double click to open Node Management

1. 1. and make the following changes. Then save and restart the PC.
      
      Image Modified

1. 1. Select AerotechNode0 at left, and go to the Kernel tab. Set "Start automatically" to Yes
      

      Expand
      title Figure 1-3
      Image Modified

1. 1. 
      

   2. Go to the System tab. Set "Boot Mode" to Dedicated
      

      Expand
      title Figure 1-4
      Image Modified

1. 1. 
      

2. Open A3200 Configuration Manager. Co to Controller > Connection Settings (toolbar dropdown). In the Advanced tab, set the "Start A3200" option to Automatically. Click Apply and OK. Restart the PC.
   

   Expand
   title Figure 1-5
   Image Modified

1. 
   

2. If none of

1. the above solutions helps resolve or narrow down the problem please

1. create a technical support case. Provide the following information:
   
   1. A3200 software version
   2. Windows Operating System version
   3. Full error message

   4. The INtime Event Viewer Log. Open Windows Event Viewer. Right-click INtime folder and click Save All Events As....

      Expand
      title Figure 1-9
      Image Modified

      
      

Cause

INtime has a problem that prevents the INtime IO services from starting.

Solution

If you installed the A3200 and you did not restart your PC, restart your PC before you use the A3200.

Cause

INtime has a configuration problem that prevents the INtime kernel from starting.

Solution

If you installed the A3200 and you did not restart your PC, restart your PC before you use the A3200.

Cause

INtime is not correctly configured on your PC.

Solution

Reinstall the A3200 and INtime. Refer to the procedure that follows.

1. Uninstall the A3200. Then restart the PC.
2. Uninstall INtime. Then restart the PC.
3. Install the A3200. Then restart the PC. The installation automatically installs and configures INtime again.

Cause

The version of INtime on your PC is not compatible with the software.

Solution

Reinstall the A3200 and INtime. Refer to the procedure that follows.

1. Uninstall the A3200. Then restart the PC.
2. Uninstall INtime. Then restart the PC.
3. Install the A3200. Then restart the PC. The installation automatically installs and configures INtime again.